Comments on: New Roughing 90% Done… Only 90% Left http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/?utm_source=rss&utm_medium=rss&utm_campaign=new-roughing-90-done-only-90-left Fri, 12 Aug 2011 12:57:41 +0000 hourly 1 http://wordpress.org/?v=3.3 By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7763 Randy Wed, 17 Jun 2009 17:23:41 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7763 2.75D roughing 2.75D roughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7762 Randy Wed, 17 Jun 2009 17:22:03 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7762 Slope roughing Slope roughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7761 Randy Wed, 17 Jun 2009 17:21:40 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7761 Z-level blended roughing Z-level blended roughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7760 Randy Wed, 17 Jun 2009 17:20:47 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7760 Streamline roughing Streamline roughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7759 Randy Wed, 17 Jun 2009 17:19:22 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7759 Z-ramp roughing Z-ramp roughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7758 Randy Wed, 17 Jun 2009 17:15:21 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7758 Smootheroughing Smootheroughing

]]> By: Randy http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7752 Randy Thu, 11 Jun 2009 19:55:45 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7752 X/treem Ruffing! X/treem Ruffing!

]]> By: Robert http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7750 Robert Wed, 10 Jun 2009 15:40:28 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7750 The new "conformal" (I need to think of a more obvious name) option will take care of that behavior. It will drape each layer over the model to leave much less stock behind. This was a huge improvement in the early test I did with my mill. -Robert The new “conformal” (I need to think of a more obvious name) option will take care of that behavior. It will drape each layer over the model to leave much less stock behind. This was a huge improvement in the early test I did with my mill.

-Robert

]]> By: Gerry http://www.grzsoftware.com/blog/development/new-roughing-90-done-only-90-left/#comment-7749 Gerry Wed, 10 Jun 2009 15:33:07 +0000 http://www.grzsoftware.com/news/2009/06/08/new-roughing-90-done-only-90-left/#comment-7749 While you're working on the roughing, can you change (fix? :) ) the issue where the bottom of the stock is not machined if there's not enough material for a full depth pass at the bottom. For example, with a depth /pass of .3 and 1" stock, can we get 3 passes of .3 and one at .1, vs the current scenario where the .1 is not touched? Thanks. While you’re working on the roughing, can you change (fix? :) ) the issue where the bottom of the stock is not machined if there’s not enough material for a full depth pass at the bottom. For example, with a depth /pass of .3 and 1″ stock, can we get 3 passes of .3 and one at .1, vs the current scenario where the .1 is not touched? Thanks.

]]>